Headline News
 Home>News Archive>2015>December>Headline News>

Prune crape myrtle trees properly

News Release Distributed 12/04/15

By Allen Owings

LSU AgCenter horticulturist

HAMMOND, La. – We’re approaching winter in Louisiana, and this is the time when crape myrtle pruning becomes commonplace. Unfortunately, these are among the most abused trees in Louisiana’s residential and commercial landscapes.

Home gardeners and landscape professionals are now pruning crape myrtles earlier in the fall. It is not unusual to see pruning on these popular plants being done in August, September and October although any pruning, when necessary, should not be done until winter.

Crape myrtles need only occasional pruning, in most cases, to obtain the desired landscape effect. But many times these plants are “butchered” for no good reason.

An unfortunate trend in crape myrtle pruning is to “lop off the tops,” which results in a crew-cut appearance. The lush growth that occurs at these cut sites in spring appears vigorous, but it’s actually structurally weak and is more susceptible to fungus diseases such as powdery mildew. Worse yet, when pruning is done improperly over several seasons, large, swollen, unsightly knobs form at the point where pruning is done each year.

Some folks refer to this pruning method for crape myrtles as “crape murder.”

Although “crape murder” does not kill a crape myrtle, why are these most popular, small flowering trees pruned this way?

The method of cutting back the main branches of a tree to the same spot every year is called pollarding. This pruning method is used on some types of trees in certain situations and tends to be more common in Europe than America.

A gardener should understand, however, that the life of a crape myrtle is shortened – and the natural beauty of the tree is destroyed – by this pruning technique. If gardeners understand this and still decide pollarding creates the appearance they desire for their trees, well, that’s their choice.

We often encounter gardeners who think they are supposed to prune their crape myrtles that way. Nothing could be further from the truth. For the overwhelming majority of us, simply enhancing the natural shape of our crape myrtles is appropriate.

Some gardeners have been told that crape myrtles need to be pruned that way to bloom well. This is not accurate. The flower clusters may be larger on pollarded trees. But the added weight on the ends of long, thin branches causes them to bend over awkwardly, especially after rain. And because the tree is smaller, it actually produces fewer flower clusters.

To prune a crape myrtle properly, first decide if it needs to be pruned. As with any pruning project, you must have a specific purpose in mind before you begin. If you can’t come up with a good reason to prune your tree, leave it alone. If you do see something that calls for pruning, study the tree carefully and determine what needs to be pruned to accomplish the specific purpose you’ve identified.

Examples of appropriate reasons for pruning include eliminating crossed and rubbing branches, removing low branches, removing weak, thin branches from the inner part of the tree, trimming off old seed pods, creating a shapelier tree and keeping suckers removed from the base of the trunk. Avoid cutting back or shortening branches larger than your finger, although cutting larger branches back to a side branch or to the trunk, when needed, is fine.

Sometimes crape myrtles are pruned improperly to create a different shape. A wide variety of crape myrtle varieties are available today. Some grow tall and upright like a vase, while others are shorter and spreading, having more of an umbrella or cascading effect. You cannot make an upright-growing crape myrtle grow into other shapes by cutting it back. The new growth will simply grow upright again. So if you want a crape myrtle that will mature in the shape you desire, make sure you choose one that naturally grows that way.

Many gardeners cut back crape myrtles that are too large for the location where they were planted. This is commonly seen in crape myrtles planted close to a building. Instead of choosing a smaller-growing variety that would be appropriate, people may plant a larger type that then begins to grow into the gutter and roof. To salvage the situation, people often begin cutting their trees back. To be effective, this has to be done every year. And again, it ruins the natural beauty of the tree. This is added work that could have been avoided by planting a smaller-growing crape myrtle.

For instance, if you want a white-flowering crape myrtle planted at the corner of your house, it would be more appropriate to select Acoma, which matures at 10 feet to 12 feet, rather than Natchez, which matures at 25 feet to 30 feet.

With its smooth, muscular trunks, peeling bark, filigree of leafless branches in the winter and exceptionally long blooming season in summer, the crape myrtle is rightfully popular here. Make sure you keep yours looking its best.

You can see more about work being done in landscape horticulture by visiting the LSU AgCenter Hammond Research Station website. Also, like us on Facebook. You can find an abundance of landscape information for both home gardeners and industry professionals at both sites.

Rick Bogren
Last Updated: 12/4/2015 1:19:30 PM

Have a question or comment about the information on this page?
Click here to contact us.